Acnodes FPC 7150 Manuale Utente

FPC 71X0 fan less panel PC 12”/15”/17” touch screen Atom all-in-one fan less system User manual

FPC 71X0 User Manual 1-2 1.2 Specifications SYSTEM CPU • Onboard Intel Atom N270 processors (1.6GHz/FSB 533MHz) • Main Chipsets: Intel i82945GS

FPC 71X0 User Manual 1-3 Resolution y FPC 7120: 800 x 600 y FPC 7150: 1024 x 768 y FPC 7170: 1280 x 1024 Brightness y FPC 7120: 350 cdm

FPC 71X0 User Manual 1-4 PS/2 • 2 x PS/2 ports (for keyboard and mouse) Audio • 1x line-out and 1x Mic in VGA • 1 x DB15 VGA interface for

FPC 71X0 User Manual 3-5 Chapter 2 USING THE SYSTEM 2.1 Identifying the System 2.1.1 Front view 2.1.2 Rear view • FPC 7120/7150/71

FPC 71X0 User Manual 3-6 2.2 First Time System Setup To set up the FPC 71X0 series for the first-time, you should have the following items ready.

FPC 71X0 User Manual 3-7 ensure the settings will not be erased when the computer is turned off or reset. When the computer is powered on again, th

FPC 71X0 User Manual 3-8 2.3 Installation Memory Module The FPC 71X0 series with BI-946ID main board provides two 240-pin DIMM slot. The socket su

FPC 71X0 User Manual 3-9 Chapter 3 INPUT/OUTPUT CONNECTORS  PS/2 Keyboard and PS/2 Mouse The FPC 71X0 series provides two connector support

FPC 71X0 User Manual 3-10  Network Interface The Realtek RTL8111B Gigabit Ethernet supports the PCI Express 1.0a bus interface for host communica

FPC 71X0 User Manual 4-11 Chapter 4 SYSTEM MAIN BOARD 4.1 Main Board Dimensions Width 170mm Length 170mm Height 33.2mm

I FCC Statement This device complies with part 15 FCC rules. Operation is subject to the following two conditionsThis device may not cause harmful

FPC 71X0 User Manual 4-12 4.2 Main Board Layout Locating Jumpers and Connectors (front side)

FPC 71X0 User Manual 4-13 4.3 Main Board Jumpers and Jumper Setting Label Function Note JP1 LVDS Panel Power Selector 3x1 header, pitch 2.0 mm J

FPC 71X0 User Manual 4-14 4.3.3 JP4: COM5, COM6 RS232 +5V/+12V Power Setting Pin Signal Name JP4 Signal Name Pin 1 RI (Default) RI (Default) 2

FPC 71X0 User Manual 4-15 4.3.6 JBT: Clear CMOS Contents JBT Setting Function Pin 1-2 Short/Closed Normal Pin 2-3 Short/Closed Clear CMOS

FPC 71X0 User Manual 4-16 4.4 Connectors and Pin Assignment The table below lists the function of each of the board’s connectors. Label Function

FPC 71X0 User Manual 4-17 4.4.1 CN1: Inverter BKL Connector Pin Signal Name 1 Ground 2 Ground 3 ENABKL 4 12V Pin Signal Name 1 +12V 2 GND 3 GND 4

FPC 71X0 User Manual 4-18 4.4.5 J1: PW/Reset Switch and Indicator Connector Signal Name Pin Pin Signal Name +5VSB 1 2 KBDATA-IN KBDATA-OUT 3 4 Gro

FPC 71X0 User Manual 4-19 4.4.8 J4: COM2+ CRT (D-SUB 9Pin+D-SUB 15Pin Connector) Signal Name Pin Pin Signal Name DCD, Data carrier detect 1 6

FPC 71X0 User Manual 4-20 4.4.10 LAN1, LAN2: RJ45 + USB0/1, USB2/3 Connectors Pin Signal Name 1 SPK_LN 2 SPK_LO 3 SPK_RN 4 SPK_RO 4.4.11 SATA1

FPC 71X0 User Manual 4-21 4.4.15 COM1: COM Port Connector Signal Name Pin Pin Signal Name DCD, Data carrier detect 1 2 DSR, Data set ready RX

II Copyright Notice This document is copyrighted, 2009. The information provided in this document has been carefully checked for accuracy at the ti

FPC 71X0 User Manual 4-22 Signal Name Pin Pin Signal Name VCC 1 2 INDEX VCC 3 4 DRV_SEL VCC 5 6 DSK_CH NC 7 8 NC NC 9 10 MOTOR DINST 11 12 DIR NC 1

FPC 71X0 User Manual 4-23 4.4.21 LCD1: LVDS Panel Output 4.4.22 MODEM1: Onboard Modem Connector Signal Name P

FPC 71X0 User Manual 4-24 4.4.23 IDE1: IDE Connector Signal Name Pin Pin Signal Name Reset IDE 1 2 Ground Host data 7 3 4 Host data 8 Host data 6 5

FPC 71X0 User Manual 5-25 Chapter 5 AWARD BIOS SETUP Power on the computer and immediately press <DEL> to run the AwardBIOS™ CMOS Setup Ut

FPC 71X0 User Manual 5-26 5.2 Award BIOS Setup Power on the computer and immediately press <DEL> to run the AwardBIOS™ CMOS Setup Utility,

FPC 71X0 User Manual 5-27 HEISEI Electronics Co., Ltd. 5.3 Standard CMOS Features The standard CMOS features setup allows users to configure syste

FPC 71X0 User Manual 5-28 HEISEI Electronics Co., Ltd. ► Capacity Note that the disk drive capacity (approx.) is usually slightly greater than th

FPC 71X0 User Manual 5-29 HEISEI Electronics Co., Ltd. 5.4 Advanced BIOS Features This section allows you to configure your system for basic oper

FPC 71X0 User Manual 5-30 HEISEI Electronics Co., Ltd.  Virus Warning Allow you to choose the Virus Warning feature for IDE Hard Disk boot sect

FPC 71X0 User Manual 5-31 HEISEI Electronics Co., Ltd.  Boot Up Num Lock Status This item defines if the keyboard Num Lock key is active when y

III Unpacking the FPC 71X0 Series After unpacking the FPC 71X0 carton, check to make sure all the following items are included and in good conditio

FPC 71X0 User Manual 5-32 HEISEI Electronics Co., Ltd. 5.5 Advanced Chipset Features These items define critical timing parameters of the mainboa

FPC 71X0 User Manual 5-33 HEISEI Electronics Co., Ltd.  Video RAM Cacheable Options: Enabled or Disabled Default: Disabled

FPC 71X0 User Manual 5-34 HEISEI Electronics Co., Ltd. 5.6 Integrated Peripherals  OnChip IDE Device ► IDE DMA transfer access Options: Enab

FPC 71X0 User Manual 5-35 HEISEI Electronics Co., Ltd.  Super IO Device ► Onboard FDC Controller Options: Enabled, Disabled Default: Enabled ►

FPC 71X0 User Manual 5-36 HEISEI Electronics Co., Ltd.  Serial Port 3 Use IRQ Options: IRQ5, IRQ7, IRQ10, IRQ11 Default: IRQ10  Onboard S

FPC 71X0 User Manual 5-37 HEISEI Electronics Co., Ltd.  USB Device Setting ► USB Controller Enable or disable Universal Host Controller Inter

FPC 71X0 User Manual 5-38 HEISEI Electronics Co., Ltd. 5.7 Power Management Setup  ACPI function Options: Disabled, Enabled Default: Enabled

FPC 71X0 User Manual 5-39 HEISEI Electronics Co., Ltd.  Suspend Mode Options: Disabled, 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min, 20 Min, 30 M

FPC 71X0 User Manual 5-40 HEISEI Electronics Co., Ltd. 5.8 PnP/PCI Configuration  Reset Configuration Data Enabled will reset the ESCD (Exten

FPC 71X0 User Manual 5-41 HEISEI Electronics Co., Ltd. 5.9 Frequency/Voltage Control  Auto Detect PCI Clk Options: Disabled, Enabled Default:

IV Important Safety Precautions 1. Before getting started, read these instructions and save them for later reference. 2. Please disconnect this

FPC 71X0 User Manual 5-42 HEISEI Electronics Co., Ltd. 5.10 Load Fail-Safe Defaults When you press <Enter> on this item, you will get confi

FPC 71X0 User Manual 5-43 HEISEI Electronics Co., Ltd. 5.11 Load Optimized Defaults When you press <Enter> on this item, you will get confi

FPC 71X0 User Manual 5-44 HEISEI Electronics Co., Ltd. 5.12 Set Supervisor/User Password Steps to set supervisor/user password are described as f

FPC 71X0 User Manual 5-45 HEISEI Electronics Co., Ltd. 5.13 Save & Exit Setup  Pressing <Enter> on this item asks for confirmation:

FPC 71X0 User Manual 5-46 5.14 Exit Without Saving  Press <Enter> on this item asks for confirmation:  Quit Without Saving (Y/N)? Y

FPC 71X0 User Manual 6-47 Chapter 6 DRIVERS INSTALLATION This chapter offers information of software drivers’ installation. 6.1 Chipset Driv

FPC 71X0 User Manual 6-48 E. Click Next. F. Click “Next” to go on. G. Select “Yes, I want to restart the computer now.”, and

FPC 71X0 User Manual 6-49 C. Click Next. D. Click Yes to accept the agreement. E. Click Next. F. Click Next. G. Select

FPC 71X0 User Manual 6-50 6.1.3 Windows POSReady 2009 A. Click the folder “Chipset”. B. Click “Setup” to install. C. Click Next. D. Click

FPC 71X0 User Manual 6-51 G. Change the path “C:\WINDOWS\ H. Change the path “C:\WINDOWS\ system32\drivers” and click OK. system32\driv

Contents CHAPTER 1 INTRODUCTION ... 1-1 1.1 General Information ...

FPC 71X0 User Manual 6-52 O. Change the path “C:\WINDOWS\ P. Change the path “C:\WINDOWS\ system32\drivers” and click OK. system32\dr

FPC 71X0 User Manual 6-53 6.2 Ethernet Driver Installation The FPC 71X0 series is equipped with the Realtek RTL8111B Ethernet controller combines a

FPC 71X0 User Manual 6-54 E. Click Next. F. Click Install to start. G. Click Finish to complete the process. 6.2.2 Windows VISTA A.

FPC 71X0 User Manual 6-55 C. Click “Vista_RTL8168_8101E_8169_ D. Click “setup” to install. 6193_070606”. E. Click Next. F. Click Install

FPC 71X0 User Manual 6-56 6.2.3 Windows POSReady 2009 A. Click the folder “LAN”. B. Click the folder “Win2k_xp”. C. Click “RTL8168_8101E_664”

FPC 71X0 User Manual 6-57 G. Click Finish to complete.

FPC 71X0 User Manual 6-58 6.3 VGA Driver Installation The FPC 71X0 series offers an integrated VGA/LCD Controller, 2D/3D GUI engine, sharing memor

FPC 71X0 User Manual 6-59 E. Click Yes to accept the agreement. F. Click Next. G. Click Next to go on. H. Click Finish to complete the p

FPC 71X0 User Manual 6-60 C. Click “winvista_1583” to install. D. Click Next. E. Click Next. F. Click Yes. G. Click Next. H. Clic

FPC 71X0 User Manual 6-61 I. Click Finish. 6.3.3 Windows POSReady 2009 A. Click the folder “VGA”. B. Click the folder “win2

4.4.13 I_SP: Internal Speaker Connector ... 4-20 4.4.14 PW_IN: DC Power In (DC12V) ...

FPC 71X0 User Manual 6-62 E. Click Yes to accept the agreement. F. Click Next. G. Click Next. H. Click Finish to complete the process.

FPC 71X0 User Manual 6-63 6.4 Audio Driver Installation The FPC 71X0 series is equipped with the VIA HD Codec VT1708A, which is delivering top qual

FPC 71X0 User Manual 6-64 G. Click Next. H. Click Next to continue. I. Click Next. J. Click Finish. 6.4.2 Windows VISTA A. Click the

FPC 71X0 User Manual 6-65 C. Click the folder “v340f”. D. Click “SETUP” to install. E. Click Next. F. Select “I Agree” and click Next.

FPC 71X0 User Manual 6-66 I. Click Next to continue. J. Click Finish. 6.4.3 Windows POSReady 2009 A. Click the folder “AUDIO”.

FPC 71X0 User Manual 6-67 E. Click Next. F. Click I Agree and click Next. G. Click Next. H. Click Next. I. Change the pat

FPC 71X0 User Manual 6-68 K. Click Next. L. Click Finish to complete the process.

FPC 71X0 User Manual 6-69 6.5 Wireless LAN Driver Installation The Users must make sure which operating system you are using in the FPC 71X0 series

FPC 71X0 User manual 6-70 6.6 Touch Driver Installation The FPC 71X0 series supports HIGGSTEC Touch. The touchscreen systems consist of a touchscre

FPC 71X0 User manual 6-71 G. Click OK. H. Click Next. I. Click Next. J. Click Next. K. Click Yes. L. Click Yes.

6.3.2 Windows VISTA ... 6-59 6.3.3 Windows POSReady 2009 ...

FPC 71X0 User manual 6-72 M. Press the blinking X Symbol until stop N. Click OK to complete the process. blinking.

FPC 71X0 User Manual 1-1 Chapter 1 INTRODUCTION This chapter includes the FPC 71X0 series system background information.  General Information